Underground Racing, a name well known and feared in the world of high speed roll racing breaks out their new weapon of choice, the Audi R8. Click to watch! Continue reading
Tag: piping
Tig’d Up Tuesday Review 2-18
Posted onBefore we give you this Tig’d Up Review, we are going to do a replay of a few previous Tig’d Up articles, showcasing previous work.
Tig’d Up Review Holiday Edition
This week, we had entries featuring Industrial, Exhaust Headers, Race Radiators, and Exhaust Systems. We tried to focus on complete parts rather than 1-10″ sections of welding. The idea was to have featured images that showcase finished products. We will be looking for that this week in our submissions as well. Good luck and submit early!
On to the Review!
David D./ D3 Performance Engineering
This thing is just sick! 321 stainless tri-Y turbo manifold all slip fit for a 2JZ with a ProMod 88mm turbo. Feature coming on this 240sx shortly on Fabricationlife.com, too…
Tig’d Up Tuesday Review 2-11
Posted onYour Tig’d Up Tuesday Review for the second week of February is here . We enjoyed another successful week of posts, and got a ton of submissions! Here they are:
Priit KukkFabrication
“This is a mic fastening point on a acoustic stand for exhaust gas analysis. Welded with a Kemppi MasterTig 4004 1,6mm 316 filler, pulse setup : 90 amp 40% duty 1hz frequency.”
Nick Primero
“Tigging away on racecars this week.”
Samuel Hoskins
“Here is some work from Ben Issacson, owner of Ground up Motorsports in Australia”
Richard Rasmussen
“Thirsty?”
Brandon Kalcsics
“Carbon to chromoly, running at 200amps. Freehand dab on a 77 honda cb750 hardtail.”
Race Ready Fab
“Civic custom exhaust 304ss machine thermal arc 186”
Derek at SpeedFactory
“Backdoor intercooler endtank with change.”
Dane Reynolds
“304ss v band clamp by tig welded by Dane from RB Garage toowoomba”
Keep the submissions flowing! See you on another Tig’d Up Review!
Tig’d Up Tuesday Review 1-21
Posted on 1This was one of our most packed Tig’d Up Tuesdays in a while. We numbers of submissions, and work from all industries sent in. We chose 10 this week, and the page saw traffic from across the globe!
As we said before, we will be featuring more than 10 entries every week now, so make sure you get your submissions in. If we do not use them, please keep sending. We may use one you send on a future post in the page.
Here are the submissions:
The Turbo Elements
“Some drops with some dimes”
FabTime: Exhaust Speaker.. Should we?
Posted on
Fabrication Life fans, we need your opinion! We posted the photo below yesterday, and we all were obsessed with it. Everything about it screamed BAD ASS! Spending the day with the materials to make this happen is even worse because we got that itch. You all know the itch… it’s a curse!
Tig’d Up Holiday Review
Posted onHappy Holidays to all of our Fabrication Life fans! Always, receiving tons of Tig’d Up Tuesday submissions, we posted a few we felt to show off. Here, we will seperate by date posted. Enjoy the selection and tell us your favorites. We are partial to the flask!
12/17/13
Ariel Banco
“5xxx series sheet. 3mm thickness. 100 amps, no pulse, 2.4mm 5356 filler rod. by Custom Plenum Creations”
Tig’d Up Tuesday Review 12-10
Posted on 1Tig’d Up Tuesday on the Fabrication Life Facebook fan page was great this week in terms of submissions! You would think 10-15 submissions would have been posted but we were just a bit busy! Thank you again to everyone who posted.
This week, we will show off a few of the submissions which did not get posted along with the posted material:
Niels Hattas
“TI-exhaust system for KTM/Nelson Welding” (Bike was built by Maarten Janssens)
Tig’d Up Tuesday Review 12-3
Posted on 1Last week was our 1st Tig’d Up Tuesday review on FabricationLife.com and the fans loved it!
This week we had a huge amount of traffic for Tig’ Up Tuesday. Here is what was posted:
Myles Blackwell
“Mild Steel weld”
